Search
Search
Search

Lookng for Chinese Manufacturer for Gradient Oven ?

What is the gradient oven ? Gradient oven is a test equipment used to test the preparing and drying attributes of paint, powder covering, pitch, plastic and different materials. It can reproduce the preparing cycle of the creation line by programming the info warming rate, heating temperature and preparing time. Utilizing a gradient oven tester can save a ton of test time and energy. Reenact different restoring temperatures on a test board and reproduce the temperature bend of the drying burrow on the creation line in the lab, which is exceptionally helpful to utilize.

The gradient oven supplied by Wewon Environmental Chambers Co., Ltd. permits scientists and quality examiners to perform synchronous testing of coatings, crude materials and synthetic compounds at various temperatures in a similar advance. It understands that the testing steps reproduced in the lab can be replicated to the real creation measure (box type or chain type open hearth). What’s more, the adaptability of the temperature setting of the gradient crystal oven can program a temperature that recreates an ideal explanatory inclination change, giving ascent, fall or other temperature reenactment conditions.

Equipment NameGradient OvenGradient OvenGradient Oven
Equipment ModelWEW-01-ASTWEW-02-ASTWEW-03-AST
Temperature Range (℃)30 ~ 25030 ~ 25030 ~ 320
Temperature Range (°F)86 ~ 48286 ~ 48286 ~ 608
Connect to FurnaceNot includedincludeNot included
Heating Rate2℃ to 30℃2℃ to 30℃2℃ to 30℃
Heating Surface520×100mm520×100mm520×100mm
Test Surface500×70mm500×70mm500×70mm
Temperature PrecisionBelow 200℃ ± 2℃|Below 250℃ ± 3℃|Below 320℃ ± 5℃
Baking TimeSet in seconds and minutes
Memory CapacityMaximum 10 Steps
Linear Gradient30℃ ~ 250℃: 100℃
Gradation2, 3, the maximum temperature difference between the two steps: 50℃
Pressure PlatformCan automatically reciprocate put in or send out the test board
Power VoltageAC 230V, 50/60Hz 3400 Watts
Acid rain, bird droppings, fuel, antifreeze and many other environmental factors can damage a car’s finish. Especially in summer, certain substances can be very corrosive and cause serious damage. Therefore, both automotive paint manufacturers and automobile manufacturers need to find out how different environmental phenomena will interact with the paint system. Concerning the subject of prepared coatings inside mechanical creation conditions, the precise control of the comparing measures is of essential significance to accomplish and ceaselessly keep up/ensure the predetermined subjective attributes of the covering. Because of various reasons, the really existing conditions don’t generally compare precisely to the preset cycle run which in the “thinking pessimistically” may cause seriously high non-similarity costs.

Compared With the laboratory oven, The gradient-oven offers the chance of a necessities based enhancing of the cycle for the item being referred to. The “actual condition” in the oven plating creation line, previously controlled by methods for a broiler temperature recorder, can be reenacted at the best by means of a necessity orientated setting of a proper slope and subsequently permits an almost ideal 1:1 recreation of the particular stoving condition, anyway on the ideal research facility scale saving time and costs.

Gradient Oven

For a variety of reasons, the actual conditions that exist don’t always correspond exactly to the preset process, In a “worst case” scenario, this could result in significant nonconforming costs. Gradient ovens offer the possibility of requirement-based process optimization for the product in question. The “actual conditions” in the furnace enamel production line determined in advance by the oven temperature recorder can be best simulated by appropriate demand-oriented gradient settings. Thus, a perfect 1:1 simulation can be achieved.

However, on the desired laboratory scale, the respective baking conditions save time and expense. Sometimes the actual conditions of a process don’t match the expected conditions. This can result in a loss in money, time and productivity. Gradient ovens can help optimize the process by simulating the actual conditions of the process through temperature recordings and demand-oriented gradient settings. This allows for a more efficient use of resources in terms of time and cost, particularly on a smaller laboratory scale.
Resins, additives, pigments, powder coatings, paints, coatings, silicones, etc.Equipment Purpose
Temperature resistance and performance stability test of resin
Analysis of coating curing process, chemical properties, thermal stability
Temperature stability of pigments and additives
Catalyst reaction, temperature stability and reaction within the temperature range
Flow, leveling and surface wettability of surface additives within the temperature range
Initiation of sample flow in the temperature range
Silicone testing and solvent products are quickly evaporated.
distribution graph of gradient oven at different temperatures

Compared With The Laboratory Oven, What Are The Advantages of Gradient Oven ?

● Test Device’s Test Area Is Fully Heated: The test floor is fixed on the glass bed outside the transparent cover and automatically smoothed to the appropriate position. Once the test baseplate reaches the heating zone, a special magnetic yoke exerts downward force on the baseplate, resulting in more thermal contact between the baseplate and the heating zone.

● Gradient Oven With Accurate Test Data: The control of the infrared heater is very precise, but the temperature transmitted to the test board itself is an uncertain factor. This problem is solved by an integrated temperature sensor that detects and controls each in-yoke heater. The current reference temperature is taken from the test board itself, which ensures that the test results are true and reliable, regardless of the shape or material of the test board itself.
Data import, oven tracking system measures and records the real production cycle, and replicates in the laboratory.Equipment Feasutres
Pre/post embedded cooling, active cooling area, cooling the test base plate through Peltier elements to optimize the test cycle.
Equipment with variable exhaust system, unnecessary gas and smoke.
Transparent cover, allowing the experimenter to observe the chemical reaction of the sample under different temperature conditions.
Rapid heating time, high temperature is almost instantaneous.
Smooth and horizontal test plate loader keeps the liquid sample in place throughout the process.
Glass bed of gradient oven from Wewon Environmental Chambers Co., Ltd. is easy to clean.
● Test Equipment’s Diversified Functions: The gradient oven produced by Wewon Tech has an ultra-wide temperature range. It can vary from room temperature to approximately +350°C and can be set for up to 30 independent zones. Its ultra-wide temperature range combined with flexible programming and ultra-fast heating makes it suitable for a wide variety of tests.

Depending on the type of gradient oven, the coating can be tested at temperatures up to +300°C. By using the duplex frame coater coating system, Two different coating systems can be applied simultaneously on the same panel. This makes it easier and saves application time and material costs. In quality control tests of baking coating systems, gradient ovens produced repeatable results many times faster than conventional convection laboratory oven. In standard tests, five different chemicals can be tested on a single panel, such as H2SO4, which mimics the atmosphere and acid rain, NaOH for car washing detergents, trypsin, brake fluids and tree resins.

The liquid coating is applied through a film applicator and film applicator. Once the sides and sides of the test panel are covered, they can also be applied by spraying. The powder coating is applied to a mask plate or a magnetic strip-covered panel by means of static electricity. The panels are coated and baked under specified processing conditions. Droplets of these various materials (approx. 0.05 mL) are placed on the test plate at appropriate intervals using pipettes. Repeat this length down the panel with an interval of about 2-3 cm.
Please enter your email, so we can follow up with you.