Search
Search
Search

Intake Manifold Leak Testing Machine for Automotive Industry

This week, Wewon has developed an intake manifold leak testing machine to use a 4 bar air pressure to make the water spray on the surface of intake manifold. The air tightness of the intake manifold has been tested to meet the industrial requirements of the automotive industry by a continuous hydrostatic test at 60 PSI. This 60 PSI intake manifold water pressure test system use water to check the leak of air tightness is a very energy saving and environmental protection method. Intake manifold leak test can simulate actual needs of natural environment to greatest extent, helping inlet manifold manufacturers to get most realistic test data.

With the successive promulgation of a number of national standards and further strengthening of vehicle waterproofing and other related requirements to improve vehicle safety, As one of the most perceivable performances by users, vehicle water management performance has been paid more and more attention by car companies. The accuracy of the intake manifold leak test ensures that vehicles are operating optimally while minimizing the risk of issues such as rough idling and decreased fuel efficiency. This is so important for performance verification of manifold-equipped heavy duty trucks and family cars.

In the automotive industry, Testing for intake manifold leaks has become a crucial aspect of vehicle development and quality control. There’s no doubt about that! The use of water as a testing tool for finding air leaks in intake manifolds has proven to be an effective method. This testing technique allows for an artificial rain test to be performed under natural conditions, eliminating the need for rainfall with strong wind speeds and ensuring that samples experience a consistent amount of water inflow, regardless of the temperature difference between the rain and the sample.

Wewon Tech's Intake Manifold Leak Testing Machine

Water spray test will judge and identify (1) the effectiveness of the intake manifold or casing against rain penetration (2) the ability of the equipment to meet its performance requirements during or after exposure to rain (3) Physical damage to the inlet manifold due to rain (4) Whether the rainwater drainage system is effective. Through the analysis of the leakage water design problems that are easy to occur in the process of automobile product development, it is shown that the water management performance design can solve all the water management problems not only by improving the water sealing performance.

Meanwhile, It also reminds product design engineers, especially general layout, body-in-white and interior and exterior design engineers, to consider water sealing in water management when designing parts; Comprehensive application of strategies such as water conduction, drainage, and foreign body intrusion prevention for drainage facilities. The intake manifold vacume leak test engineer should establish an effective collaborative design mechanism with each component engineer to jointly determine the water management performance plan and reduce design errors.

What Are the Contents and Standards of The Vehicle Rain Test ? The automobile rain test has become an indispensable production link in the industry. The leak testing of air intake manifold refers to the water flowing into the car from the outside of the car body through the matching gap of the car body. The vehicle manufacturer uses artificially simulated rainfall environment to realize the rain sealing performance test.

related page logoLeak Detection Methods: A Comparative Study of Technologies and Techniques Short Version|How to Diagnose and Fix An Intake Leak ? How to Test for Exhaust Manifold Leak
related page logoAutomotive Engine Leak Test Machine | Automotive Components Leak Test Machine|Electric/Hydraulic/Household Apparatus Leak Test Machine | Medical/Pharmaceutical/Food packages Leak Test Machine
related page logoWhat is Air Leak Testing ? Advantages of Air Leak Testing|Air Leak Testing Methods|What’s the Difference Between Air Leak Testing & Pressure Testing ?
Cars produced in China now generally use GB/T12480-1990 Test method for rainproof sealing of passenger cars|Q/CAQ-16-2010 Commercial vehicle cab assembly rain tightness test specification|QC/T476-1999 The limit of rainproof sealing of passenger cars|The integrated and revised standard is QC/T476-2007 Limits and test methods for the rain-tightness of passenger cars. According to the requirements of GB/T12480-1990, the rainfall intensity of the rain test chamber is 4~10mm/min, the injection pressure of the nozzle is 69~147kPa, and the raining time is 15 minutes.

In the actual operation process, in order to strengthen the inspection of the rain sealing performance of the vehicle, the car manufacturers for automotive industry often increases the rain intensity by increasing the density of the nozzle and increasing the water spray pressure. The rainfall intensity of the rain test laboratory will be several times higher than the recommended value, and some manufacturers even exceed 100 mm/min. The spray pressure of the nozzle will also reach more than 200kPa, so that the spray water is atomized and sprinkled on the body.

Intake Manifold Leak Testing Machine for Automotive Industry

At different stages of vehicle production, cars manufacturers have different test requirements for vehicles. During the trial production period of the vehicle, at this stage, since the production process and equipment parameters of the whole vehicle are in the test period, it is necessary to pass a long-term rain test (between 4 and 8 hours) of the whole vehicle to find out the parts that may leak, and then conduct water leakage cause analysis and design or process improvement.

When the whole vehicle is mass-produced, the design and process defects are basically improved, and routine inspections are mainly carried out in the rain to prevent the sealing defects caused by occasional non-compliance. Special vehicles such as power supply vehicles, vans, road sweepers, military equipment, etc., these vehicles have high requirements for water resistance. When necessary, especially for new product development, rain test is a necessary test link. Based on the type and practicability of the special vehicle, the rain test equipment for the special vehicle is designed and implemented.

related page logo60 PSI Manifold Pressure Test System|Water Spray Test for Intake Manifold|Solves Leak Testing of Air Intake Manifolds|The Safe Way for Leak Testing (1)
related page logo60 PSI Manifold Pressure Test System|Water Spray Test for Intake Manifold|Solves Leak Testing of Air Intake Manifolds|The Safe Way for Leak Testing (2)
related page logo60 PSI Manifold Pressure Test System|Water Spray Test for Intake Manifold|Solves Leak Testing of Air Intake Manifolds|The Safe Way for Leak Testing (3)
related page logo60 PSI Manifold Pressure Test System|Water Spray Test for Intake Manifold|Solves Leak Testing of Air Intake Manifolds|The Safe Way for Leak Testing (4)
related page logo60 PSI Manifold Pressure Test System|Water Spray Test for Intake Manifold|Solves Leak Testing of Air Intake Manifolds|The Safe Way for Leak Testing (5)
related page logo60 PSI Manifold Pressure Test System|Water Spray Test for Intake Manifold|Solves Leak Testing of Air Intake Manifolds|The Safe Way for Leak Testing (6)
The main advantages of plastic intake manifolds are lower cost and lighter weight. In addition, due to the lower thermal conductivity of PA, HDPE than aluminum, the fuel nozzle and incoming air temperature is lower. The intake manifold can not only improve the hot start performance, increase the power and torque of the engine, but also avoid the heat loss in the pipe to a certain extent during cold start, and accelerate the increase of the gas temperature. And the smooth inner wall of the plastic intake manifold reduces air flow resistance, thereby improving engine performance.

In terms of cost, the material cost of plastic intake manifold and aluminum intake manifold is basically the same. The plastic intake manifold is formed at one time, with a high pass rate; The aluminum intake manifold blank casting yield is low, and the machining cost is relatively high. Therefore, the production cost of plastic intake manifolds can be reduced by 20%-35% compared with aluminum intake manifolds.
High Temperature Resistance|The plastic intake manifold is directly connected to the engine cylinder head, and the temperature of the engine cylinder head can reach 130~150℃. Therefore, the plastic intake manifold material is required to withstand a high temperature of 180°C. Requirements for Plastic Material of Engine Intake Manifold
Dimensional Stability|The dimensional tolerance of the connection between the intake manifold and the engine is very strict, and the installation of sensors and actuators on the manifold must also be very accurate.
Chemical Stability Test|Plastic intake manifold is in direct contact with gasoline and antifreeze coolant during operation. Gasoline is a strong solvent, and ethylene glycol in coolant will also affect the performance of plastic. The chemical stability of the plastic intake manifold material is required. Very high and needs to be rigorously tested.
High Strength Requirement|Plastic manifold is installed on engine, and must bear vibration load of automobile engine, the inertial force load of throttle valve and sensor, the pulsating load of the intake pressure, etc., and also ensure that it will not be blasted by the high-pressure pulsating pressure when engine is abnormally tempered.
Thermal Aging Stability|The automobile engine works under very harsh ambient temperature, and the working temperature varies from 30 to 130 ℃. The plastic material must be able to ensure the long-term reliability of the manifold.
Please enter your email, so we can follow up with you.