Search
Search
Search

Main Screen of Control System|EN 14360 Rain Tower Test System

The booming outdoor recreation industry is fueled by a growing desire for health and well-being. However, Even with the increasing use of waterproof fabrics, A critical gap exists between material performance and real-world functionality. Stitch holes created during garment construction can compromise waterproofness, Allowing water to penetrate despite seam sealing tapes. This leakage can lead to discomfort, reduced insulation, and a disappointing outdoor experience.

This controller can work normally on general occasions. If concerned about major accidents or equipment damage, set up an emergency stop circuit and protection circuit. Regarding the Control System
Controller provide power supply within rated voltage range to prevent controller failure. Do not turn on power until installation and wiring are finished to prevent electric shock or malfunction.
Do not use the control system in environments with flammable or explosive gases as it is non-explosion-proof.
Unauthorized actions like disassembly, processing, modification, or repair are strictly prohibited to avoid abnormal behavior, electric shock, or fire hazards.
Avoid touching power terminals post-power-on to prevent electric shock or malfunction. Disconnect wiring only after turning off power to prevent electric shock or misoperation.
Use 3 wires with equal resistance value and less than 10Ω when connecting temperature measurement resistor (PT100) input to avoid display errors or abnormal actions.
When performing operations on the controller, ensure safety measures are considered to prevent equipment damage or failures.
Do not use alcohol, gasoline, or other solvents on the controller. Keep it dry, prevent water exposure, and immediately stop use if immersed in water to avoid leakage, electric shock, or fire.
Dispose of the product properly as industrial waste when scrapping. Note: Touch screen and PLC control board use RS-485 communication.
[Figure 1-1] Main Screen
[Figure 1-1] Main Screen
1 MAIN MENU Screen Main Screen Introduction
Indicative Content Content Description
①   Curve&Save Switch to curve display and curve storage, and use the SD card to store the Settings Screen.
② Monitor Screen Switch to the Run Screen.
③  Operation Setting Set screen to switch function and operation mode.
④   Program Group Setting Switch to Program Setting Main screen.
⑤   Reserve Set Switch to the current time and reservation time set.
⑥ Display Screen Setting Switch to screen protection time setting and Version screen.
▶ [1.1 Main Screen] Select the “monitor screen”, You can switch to the ” FIX Operation First Running screen”. 2.1 FIX STOP –First Stop Screen 2 FIX Operation
▶ [2. Running operation setting] choose the running mode with “FIX”.
[Figure1-2] FIX Stop -First Stop Screen
[Figure1-2] FIX Stop -First Stop Screen
▶ Click the Settings button to enter the setting screen.
[Figure1-3] Setting Screen
[Figure1-3] Setting Screen
▶ The input and operation of temperature setting are as follows.
[Figure 1-4] Temperature Setting Value Input Box
[Figure 1-4] Temperature Setting Value Input Box
▶ When you enter the temperature setting point, click the red key on the upper left side to activate the temperature setting input box [Figure 1-4 temperature setting input box].
▶ The input and operation of the humidity setting are as follows.
[Figure1-5] Humidity Setting Value Input Box
[Figure1-5] Humidity Setting Value Input Box
▶ When you enter the humidity setting value, click the blue key on the upper right side of the right side to activate the humidity setting input box [Figure 1-5 humidity setting value box].
▶ After entering the temperature setting value, select the “RUN” key on the lower right side and execute the fixed value operation.
Table 3-1. Temperature, Humidity SP Parameters
Talbe 3-1 Temperature Humidity SP Parameters
[Figure 1-6] FIX Operation –The 1st FIX RUN Screen
[Figure 1-6] FIX Operation –The 1st FIX RUN Screen
2.2 FIX Operation –The 1st FIX RUN screen
① The current running state.
② The current temperature setting value and the current temperature.
③ The current humidity setting value and the current humidity.
④ The total running time.
⑤ The real-time fault information display.
⑥ The keys to stop the run of the fixed value.
☞ Display (run) key under a fixed stop screen.
⑦ Switch to the fault query screen.
⑧ Setting screen
⑨ Switch to the “FIX Operation–The 2nd FIX RUN screen”.
⑩ Switch to the main screen.
⑪ Show the current time / date.
▶ The display screen of command value, setting value, control output value and lamp action state. 2.3 FIX Operation –The 2nd FIX RUN screen
[Figure 1-7] FIX Operation –The 2nd FIX RUN Screen
[Figure 1-7] FIX Operation –The 2nd FIX RUN Screen
① The ON state is expressed in red, and the OFF state is expressed in gray.
② The current PID number.
③ The total running time.
④ The current value of humidity output of control.
⑤ The current value of temperature output of control.
⑥ 【HUMI-AT】Humidity Auto-Tuning button.( Hidden when stopped)
⑦ 【TEMP-AT】Temperature Auto-Tuning button. (Hidden when stopped)
※The key ⑥、⑦ is inactive in the stop operation of the fixed value operation.
▶ [1.1 Main Screen] Select the “Monitor Screen”, You can switch to the ” Program Operation First running screen”. 3.1 PROGRAM STOP –The 1st Stop Screen 3 PROGRAM Operation
▶ [2. Running operation setting] choose the running mode with “Program”.
▶ Refer to the [3.1 program group mode] to set mode.
▶ [Figure 1-7 PROGRAM STOP–The 1st Stop Screen] Click on the lower right side of the run button to switch to [Figure 1-8 PROGRAM First Running Screen].
[Figure 1-8] PROGRAM STOP –The 1st Stop Screen
[Figure 1-8] PROGRAM STOP –The 1st Stop Screen
[Figure 1-9] PROGRAM Operation –The 1st RUN Screen
[Figure 1-9] PROGRAM Operation –The 1st RUN Screen
3.2 PROGRAM Operation –The 1st RUN screen
① The current running state.
② The current temperature setting value and the current temperature.
③ The current humidity setting value and the current humidity.
④ The total running time.
⑤ The real-time fault information display.
⑥ The keys to stop the run of the fixed value.
☞ Display (run) key under a fixed stop screen.
⑦ Switch to the fault query screen.
⑧ The current pattern number.
⑨ Switch to the “FIX Operation–The 2nd FIX RUN screen”.
⑩ Switch to the “Main Screen”.
⑪ Show the current time / date.
▶ The display screen of command value, setting value, control output value and lamp action state. 3.3 PROGRAM Operation –The 2nd RUN Screen
[Figure 1-10] PROGRAM Operation –The 2nd RUN Screen
[Figure 1-10] PROGRAM Operation –The 2nd RUN Screen
① The ON state is expressed in red, and the OFF state is expressed in gray.
② The currently running Number of program segments.
☞ [SEG NO.: 000/000] The preceding number indicates the segment that has been executed, and the latter number indicates the setting times.
③ The pattern repeated state.
☞ [Pattern repeat : 000/000] The numbers in front represents the number of repetitions that have been executed, and the numbers in the back indicates the number of repetitions.
④ The current PID number.
⑤ The total time of the current program.
⑥ Displays the running process time / total process time.
☞ [SEG TIME : 000.00/000.00] The front number indicates the time has processed of segment and the back number indicates total process time for current segment on [3.1 Program PATTERN setting].
⑦ Displays segment repeat status.
☞ [Segment Repeat : 000/000] The front number indicates total number for repeat process and the back number indicates completed repeat process number.
⑧ Terminates the current active segment and forces it to the next segment.
⑨ HOLD ON or HOLD OFF the current temperature, humidity, light set value.
▶ Auto-Tuning is a strong function to establish optimal PID value automatically by calculating the characteristics of the control system. 4 AUTO TUNING and TUNING POINT
▶ While generating ON/OFF control output signal for 2.5 cycles, the controller measures the PV response of the control system with a limit cycle method and calculate the optimal P.I.D value with the oscillation data.
▶ Auto-Tuning process can be carried out on FIX RUN state, and after completion of Auto-Tuning process, calculated P.I.D value with SP will be automatically stored on P.I.D parameters of corresponding zone.
▶Auto tuning procedure with a set point
Auto tuning procedure with a set point
[Figure 1-11] The Real-Time Fault Display Screen
[Figure 1-11] The Real-Time Fault Display Screen
5.1 The Real-Time Fault Display Screen 5 Fault Display Screen
① The current fault content indicates that the green light indicates failure.
② Fault reset button.
③ Fault silencing button.
④ Switch to the history of the fault screen.
⑤ Back to the “Monitor Screen”.
[Figure 1-12] The History of the Fault Screen
[Figure 1-12] The History of the Fault Screen
5.2 The History of the Fault Screen
① Historical date selection can be used to query past historical failures.
② Clear the historical faults (long press valid).
③ Switch to the real-time fault display screen.
④ Back to the “Monitor Screen”.

Operation Settings of Control System|Rain Tower Testing Machine|While meeting the EN 14360 standard is crucial for military garment waterproofness, Wewon Environmental Chambers goes a step further. Understanding the demanding conditions soldiers face, Wewon offers rain tower systems with customizable settings. This allows for simulating various rain intensities, wind speeds, and even angled downpours, replicating real-world scenarios like torrential storms or constant drizzle. Read more…


Program Settings Guide|EN 14360 Waterproofness Test Equipment|In the realm of climate testing equipment, The advent of sophisticated control systems has revolutionized the way rain tower test systems operate. At the core of this technological advancement lies the intricate web of program settings that govern the functionality and efficiency of these systems. In this article, We delve into the critical aspects of program settings within the context of the EN 14360 rain tower test system, Shedding light on how these settings contribute to the efficacy of protective clothing against rain and the overall protection against rain. Read more…


Curve Display|Screen Display Setting|Reserve Setting Guidance|In the realm of environmental chambers and testing equipment, The evolution of rain tower systems has been crucial in ensuring the quality and reliability of products exposed to various weather conditions. One key aspect that contributes significantly to the effectiveness of rain tower testing is the utilization of curve display, Screen display setting, and reserve setting functionalities. These features not only enhance the precision and accuracy of test results but also streamline the testing process, Ultimately leading to improved product development and performance evaluation. Read more…

Please enter your email, so we can follow up with you.